Six errors of automatic transmission

     Misunderstanding 1 automatic transmission vehicles stop for a long time, the shift lever is still hanging in the D block

     Equipment for automatic transmission vehicles waiting for thesignal or the traffic jam, some drivers often shift rod will bemaintained in the D block, at the same time, the brake pedal, if time is very short, it is allowed. But if the long parking time is best to change into the N block (neutral), and apply the parking brake.Because of the shift lever in the D gear, automatic transmissioncars are generally weak forward, if long time stepping on the brake pedal, is forced to stop this advancement, transmission oil temperature rise, oil is easy to deteriorate, especially in the operation of air conditioning systems, the engine idle speed is higher in the case of more unfavorable.

Marine Gearbox

     Misunderstanding 2 automatic transmission vehicle speed ordownhill, the shift lever shift gear sliding on the N

    Some drivers to save fuel, at high speeds or downhill, the shift lever shift to N sliding block, which is likely to burn out the transmission. Because the transmission output shaft speed is veryhigh, and the engine idling, transmission oil pump oil supply shortage, lubricant deterioration, but also on the internal multi plate clutch transmission speaking, although the power has been cut off,but the passive film in the wheel driven by high-speed operation,the active sheet speed engine drive is very low, the two gap is small, easy to cause the resonance and skid phenomenon, have adverse consequences. The present slope needed to slide, shift lever can be maintained in the D sliding block, but can not make the engine flameout.

    Misunderstanding 3 outside of the automatic transmission P or Ngear to start the engine

Some drivers gear starting engine other than P or N, although the engine cannot run (because the chain protection, only in the P and N block to start), but there may be damage to transmission neutralstart switch. Because the automatic transmission is provided with a neutral start switch. The transmission is only available in the P or Nblock to start the engine, to avoid the car started to flee the other gear error when starting. Therefore, before starting the enginemust confirm the shift lever is in the P or N block.

    Push the vehicle to start the engine by misunderstanding 4equipped with automatic transmission or three element catalytic converter of automobile

    Equipped with automatic transmission and three element catalytic converter for battery power car not starting, but by people pushdrag or other vehicle starting, this is very wrong. Because, themethod is not to transfer the power to the engine, it will damage thethree way catalytic converter.

     Do not use the parking brake misunderstanding 5 automatic transmission vehicle parking ramp time

Cars equipped with automatic transmissions stops when the slope,some drivers just block the use of P, without the use of the parking brake, so easily lead to accidents. Because although the cars equipped with automatic transmissions in P gear with the parking lock is generally very few failure, but once the failure will cause an accident. Therefore, in the parking ramp, should use the parking brake.

Misunderstanding 6 automatic transmission cars as long as D keeps off the start, has been increasing the throttle can change to a high gear

    Some drivers think that as long as the D block starts, has been increasing the throttle can change into high gear, but this is a mistake. Because the shifting operation should be "rises to keep off ahead of time, stepping on the accelerator to downshift". It is inthe D block after the start, keep the solar term door opening 5%,up to 40km/h, quickly release the accelerator pedal, can be raised to a stop, and then accelerated to 75km/h, release the accelerator pedal and can improve a gear. According to the driving speed is reduced, a step on the accelerator, namely back low block. It must be noted, the accelerator can not be stepped on to the end.Otherwise, will be forced to hang into the low gear, may result in transmission damage.

    In short, the automatic transmission car compared with the manual transmission car, eliminating the clutch pedal, not frequently pedal,the car driving more simple, easy. But if the improper operation, willartificially increase the automatic transmission fault rate, reduce itsservice life. The correct use of automatic transmission, not only can avoid or reduce the occurrence of faults, but also can reduce the oil consumption, reduce pollution. 

     Chinabase Machinery is a group of manufacturing facilities, offering one-stop solution for mechanical power transmission products in China. We can supply a full-range of power transmission products, such as chains,Transmission Chain， sprockets and plate wheels, pulleys, gearboxes, motors, couplings, gears and racks. Our product range also covers locking assemblies (clamping elements/locking device), taper bushes, QD bushes, bolt-on hubs, torque limiters, Y2 Series Motor，shaft collars, Bevel Gears，motor bases and motor slides, chain detachers, chain guides, universal joint,V belts， rod ends and yokes. Our products are used in many different industry sector, like in automation engineering, drive engineering, conveyor technology, assembly and handling technology, packaging industries, the beverage, food and medical engineering, pharmaceutical production, and laboratory equipment.